If you are human, leave this field blank.

SRD - Request for Quote Form

Configure SRD

Select the required options for the inline process viscosity and density meter SRD. You can download SRD-Datasheet for an overview.(* indicates required)

Material

Sensor probe wetted part

Stainless steel 316L (1.4435)

C22: Hastelloy C22 (2.4602)

Product Approvals (if required)

EX-certified sensor required:

Not required

IECEx

ATEX

Installation Location (for ATEX certified sensor)

Country

Language (for ATEX requirements) Please state language in which you would like to receive the DoC (Declaration of Compliance) and Safety Information.

Do you need an EHEDG certified sensor?

Yes

Sensor Options

Density Range (select one) *

D1 : 0.0 - 1.5 g/cc : Standard range ( 0 -1500 kg/m3 ¦ 0.0 - 12.5 lb/gal )

D2 : custom : Customer specified density range up to max. 4 g/cc ( max. 4000 kg/m3 ¦ 33.4 lb/gal )

If you selected D2 above, specify the density range for your process fluid (max. 4 g/cc ¦ 4000 kg/m3 ¦ 33.4 lb/gal)

Density Calibration (select one) *

DCAL1 : Standard density calibration accuracy 0.01 g/cc ( 10 kg/m3 ¦ 0.083 lb/gal ) (Calibrated range 0.4 – 1.5 gm/cc)

DCAL2 : Higher density accuracy 0.001 g/cc ( 1 kg/m3 ¦ 0.0083 lb/gal )

If higher accuracy is required, specify the density range and accuracy required

Viscosity Range (select one)

V1 : 1 - 3000 cP : Standard range

V2 : max. 10,000 cP : Extended range

Viscosity not required

Viscosity Calibration (select one)

STD : Standard viscosity calibration accuracy

CUS : Customer specified viscosity calibration accuracy - specify viscosity setpoints in input box below

Not applicable

If you selected CUS above, specify the viscosity setpoints and accuracy required

Electronics (select one) *

Please refer to the Electronics and Communications Page for more information.

E1 : SME-TRD : Transmitter housing with display

E2 : SME-TR : Transmitter housing with solid cover

E3 : SME-DRM : DIN-rail mount housing

Communication

Rheonics electronics are pre-configured with the following communication options.

C1 : 4-20 mA : 3 channels of 4-20 mA analog signal

C2 : Modbus RTU (RS-485) : Modbus RTU over RS-485

C3 : USB : USB 2.0 compliant service and data acquisition port

C4 : Ethernet : Ethernet active on RJ45 connector

Additional FieldBus Communication Options

C5 : Bluetooth LE 4.0 : Bluetooth module for short range communication (only for E1)

C6 : Modbus TCP (Article)

C7 : Ethernet/IP (Article)

C8 : HART (Article)

C9 : Profinet (Article)

Temperature (select one) *

Note: With EX-SRD, the T4 option below is not available and T3 is only up to 185°C

T1 : 125 °C : Sensor rated for operation in process fluids up to 125 °C (250 °F)

T2 : 150 °C : Sensor rated for operation in process fluids up to 150 °C (300 °F)

T3 : 200 °C : Sensor rated for operation in process fluids up to 200 °C (400 °F)

T4 : >200 °C : Sensor rated for operation in process fluids above 200 °C (400 °F)

If you selected T4 above, please specify the maximum working temperature :

Pressure (select one) *

Note: For X5 long insertion sensor probes, maximum pressure rating is 100 bar (1500 psi).

P1 : 15 bar (200 psi) : Sensor rated for process fluids pressure up to 15 bar (200 psi)

P2 : 70 bar (1000 psi) : Sensor rated for process fluids pressure up to 70 bar (1000 psi)

P3 : 200 bar (3000 psi) : Sensor rated for process fluids pressure up to 200 bar (3000 psi)

P4 : 350 bar (5000 psi) : Sensor rated for process fluids pressure up to 350 bar (5000 psi)

P5 : 500 bar (7500 psi) : Sensor rated for process fluids pressure up to 500 bar (7500 psi)

Process Connection (Select one) *

X1 : 3/4" NPT threaded probe (Article)

X1 : G 1/2" BSPP threaded probe (Article)

X2 : Probe with Flange, specify flange DN/PN in box below (Article)

X3 : Probe with Tri-Clamp, specify TC norm & size in box below (Article)

X4 : Flush probe, specify flange type, norm & size in box below (Article)

X5 : Long insertion probe (FPC), select A & B in X5 section below (Article)

X6 : Slimline probe (SLP), select A & B in sections below (Drawing)

X7 : Reactor probe (RP), select L & B in sections below (Drawing)

X8 : Teletube probe (TT), select A & B in sections below (Article)

For X2, X3, X4: Specify type, norm and size of process connection:

For X5, X6, X7 and X8: Use the following fields to specify further configuration

A: Insertion Length - For X5, X6 and X8, input insertion length of probe, A (in mm) in box below. Specify unit if other than mm.

L: Total Probe Length - For X7

B: Process connection type, norm and size - For X5, X6, X7 and X8

Configuration drawings of the X5 long insertion sensor probe with various process connections :

Long insertion probe configuration drawings

Flange (Drawing)
DIN11851 (Drawing)
Triclamp (Drawing)
Threaded (Drawing)
Varinline (Drawing)

Sensor Cable (Select length) *

For custom cable length - specify length in meter or feet :

M12 Connection Type

See reference pictures for straight connection and 90° angled connection

Straight

90° Angled

Select all accessories that are required

Please refer to Accessories Page for list of accessories and their details.
Note: EZB-03X : For EX-SRV, Zener barriers are automatically added to order.

IFC-34N-SRD: Inline adapter for 3/4" NPT sensor probe

IFC-15T-34N-SRD: Inline adapter for 1.5" TriClamp sensor probe

TMA-34N: Tank mount adapter for 3/4" NPT sensor probe

TMB-TRX: Transmitter Mounting Bracket

THX-SS: Stainless steel transmitter housing - additional surcharge

WOL-34NS: 3/4" NPT sensor weldolet for 2" pipes

WOL-34NL: 3/4" NPT sensor weldolet for pipes bigger than 2" or tanks

HAW-12G-MTK: G1/2" Hygienic weldolet with metal seal for thick walls

HAW-12G-OTK: G1/2" Hygienic weldolet with O-ring seal for thick walls

HAW-12G-MTN: G1/2" Hygienic weldolet with metal seal for thin walls

HAW-12G-OTN: G1/2" Hygienic weldolet with O-ring seal for thin walls

SCC-SRX: Calibration cylinder

SCS-00A: Calibration stand

SPS-SRX: Protective sleeve for SRV/SRD

IMS-SR: Impact shield for sensor probe

STCM-STD: SRD thermal control module

FET-15T-15T: Tri-Clamp flow elbow tee

FTP-15T-XXX: Tri-Clamp spool piece

Applications & Industries

Select the applicable industry/industries, where you are looking to use the sensor. *

Printing and Coating

Industrial Mixing And Grinding

Food And Beverages

Energy And Hydrocarbons

Petrochemicals

Chemical

Automotive

Paper And Packaging

Life Sciences And Medical

Pumping And Pipeline

Marine

Mining, Minerals And Metals

Others

What is your application? Provide a brief introduction to your process. *

Explore how these sensors are used by other customers for your application in our knowledgebase

Ordering Information

Quantity required *

Additional Comments/Message

Brief description about the application, any other requirements specific to the quote

Requested Date of Delivery

Contact Information

Name of contact person *

Name of company *

Type of company/organization *

Please select the option which best describes your company/organization

E-mail *

Address *

Country

Phone *

Please provide your contact number.

Extension

Company Website

Privacy Notice

By clicking submit, you acknowledge that you have read the Privacy Notice.

Sales Terms and Conditions

By clicking submit, you agree to our Sales T&C.

Captcha *

reCAPTCHA is required.

If you are unable to submit this form, you can download the RFQ form as a pdf file. Select the options and fill the information requested and email to